ANTIDOTE: EXTERNAL, flush thoroughly with fresh water Additionally, water-based dye is easy to use. Van Dyck Crystals (genuine walnut crystals) make an excellent and inexpensive base from which to mix wood tones.
It’s a dye. I am using some tiger maple on a project and want the curl to really stand out. Prepare a dye bath by dissolving 1 pound of aniline blue (soluble in spirit) in 10 gallons of water, and set it aside to settle.Meanwhile prepare a mordant while boiling 35 ounces of sumac (or 5.5 ounces tannic acid in 30 gallons of water) and then dissolve therein 17 ounces of curd soap.Boil up and filter. Top coat with At Least a sanding sealer, and better, finish coats containing UV (ultraviolet light) inhibitors. We use aniline dyes mixed in water, sprayed on, wiped off and left to dry, and spray water-base topcoat over the dye, and have no problems. You do know by now that anything placed in direct sunlight is going to fade. AVOID BREATHING POWDER, and AVOID CONTACT WITH SKIN OR EYES. You’ll be able to pre-order the DVD beginning sometime after September first. What’s the difference? If not, then stay with Minwax. (I’ve forced more than one piece to dry more quickly with a hand-held hairdryer.) Here’s why. Nitrobenzene is commonly used in the process of manufacturing synthetic rubber, dyes, and pharmaceuticals—namely, acetaminophen. We no longer use oil-base products after using the aniline dyes and would never go back. Information and Application Guidelines: The water soluble anilines are best for light fastness, transparency of colour, accentuating the wood grain, ease of application, lack of lap marks and use under lacquer. Here are some supplies and tools we find essential in our everyday work around the shop. WARRANTY: Wood Finish Supply and/or the vendor assume no responsibility expressed or implied, Yes, water is a solvent and water-based aniline dye is what I’ve used for my entire woodworking career. And oil-based dye has such an extended drying time that you may lose a couple days in the shop watching oil dry. If you use an oil-based dye then brush on a coat of oil or oil-based finish, there’s a chance, a good chance, that your dye will run or move as the brush strikes the surface. However, this does not impact our recommendations. In very low concentrations, nitric acid is used as a wood treatment to create an artificial patina on pine and maple. It’s almost error proof. The following steps are recommended if you wish to assure the best in fade resistance; Use Fresh Solutions, thoroughly saturate the wood with dye 2 or 3 times. And the biggest reason, especially if you’re brushing your finish, is topcoat compatibility. That’s another mark in the easy-to-use column.For more information about finishing your project with aniline dye and how to make your furniture’s finish stand out, pick up the newest DVD “Finishes That Pop” from the WoodWorker’s Bookshop (woodworkersbookshop.com). Keep notes and make a test on a scrap of the same wood as to be dyed, evaluate colour after wood is dry. ------ KEEP OUT OF THE REACH OF CHILDREN ------ DO NOT TRANSFER TO UNLABELED BOTTLES OR CONTAINERS. Aniline products are used to manufacture a variety of end-products, ranging from polyurethane foam to Kevlar™ aramid fiber to pharmaceuticals. Chemical structure of aniline. Unreacted aniline should not be used in consumer products where ventilation or protective clothing controls are not available to protect against the consequences of accidental spills. – Simple Woodworking Projects. As a result, dye travels wherever the solvent travels, and that’s deeper into the wood than stains. Are you spraying the dyes? But what solvent (alcohol, oil or water) should you use in conjunction with the dye? TO MIX: Dissolve aproximately (1 oz. Creating a better world through responsible chemistry. It does fade, but it fades at a much slower rate than either the alcohol- or oil-based dyes. 3 - Remember that the wood tone will show through & blend with the dye colour for your final result. Compared to alcohol-based dye that dries so quickly, the water-based mixture precludes lap marks, especially if you apply the dyes as I do. Many chemicals can be made from aniline, including: Persons considering the use of aniline should be aware of its hazards and take necessary steps to ensure safe handling. Cool to room temperature prior to use.
That adds depth to your finish. in 2 Quarts) or (1/2 Pound in 1 Gallon) of hot (not boiling) water. Unreacted aniline should not be used in consumer products where ventilation or protective clothing controls are not available to protect against the consequences of accidental spills. STORAGE: It is best to mix what will be used within a short period of time. 1 - For consistent results use distilled water & mix powder by weight. Nitrobenzene However, nitrobenzene can also be used to produce lubricants for motors and other machinery, and as an inexpensive perfume used in soaps or to mask the odors of shoe polishes and solvents.
ANILINE DYE Water Soluble. And who wants to worry with oily rags when the process is complete? That’s an easy call , water. It is also used as a solvent, and has been used as an antiknock compound for gasolines. Water-based aniline dye is the least likely aniline dye to fade in sunlight. Ditto if you’re using alcohol-based dye and applying a coat of shellac.
©2020 The Chemours Company. Wash Hands thoroughly with soap and water Immediately after use. Can I use a wipe-on polyurethane like Min-wax over a water based dye? These tips should be followed after properly mixing dyes. Aniline is primarily used in the production of methylene diphenyl isocyanate (MDI) to create rigid polyurethane foams as insulators for refrigerators, freezers, and buildings. It works well in the creation of pigments and dyes as well. Connect with experts to learn more about Aniline products and to find the right solution for your needs.