This lab will test your ability to configure basic settings such as hostname, motd banner, encrypted passwords, and terminal options on a Cisco Catalyst 2960 switch simulated in Packet Tracer 7.2.1. Use the console connection on PC-A to display and verify the switch configuration. • Configure basic switch settings. You are prompted to remove the configuration file. g. Verify that the static MAC address has been cleared.
b. g. Configure the virtual terminal (vty) lines for the switch to allow telnet access. a. Connect the console cable as shown in the topology. In this step, you will examine the default switch settings, such as current switch configuration, IOS information, interface properties, VLAN information, and flash memory. Display the MAC addresses using the show mac address-table command. 8) Click the Use the following IPv6 address radio button and enter the IPv6 address and prefix and How many total static MAC addresses are there?
Without the login command, the switch will not prompt for a password. If no default gateway is set, the switch cannot be managed from a remote network that is more than one router away. You will also demonstrate the use of a management IP address for remote switch management. In this lab, you will build a simple topology using Ethernet LAN cabling and access a Cisco switch using the console and remote access methods. A sample configuration is shown here. If your switch does not have a default configuration, erase and reload the switch. If you have entered the name correctly, press Enter; otherwise, you can change the filename.
What is the filename of the Cisco IOS image? 4) Right-click an Ethernet interface, and choose Properties. A default gateway is not required for this topology; however, you can enter 192.168.1.1 and fe80::1 to simulate a router attached to S1. Use the show flash command to determine if any VLANs have been created on the switch. Cisco switches have the no shutdown command configured by default on VLAN 1, but VLAN 1 won’t reach the up/up state until a port is assigned to it and this port is also up. • 1 PC (Windows with terminal emulation program, such as Tera Term) b. Verify the management VLAN 99 settings. The default configuration is to allow all console connections with no password needed. click OK. Access to privileged EXEC mode should be restricted by password protection to prevent unauthorized use because it provides direct access to global configuration mode and commands used to configure operating parameters. Notice in the above output that the VLAN 1 interface goes down because none of the ports are assigned to VLAN 1. Note: Make sure that the switches have been erased and have no startup configurations. 2.9.1 Packet Tracer – Basic Switch and End Device Configuration – Instructions Answer 26/12/2019 Last Updated on 06/09/2020 CCNA 1 Labs - Packet Tracer , CCNA v7 Course #1 , … Respond by typing no and press Enter. To specify which ports a host can connect to. Press Enter to proceed. To remove the existing MAC addresses, use the clear mac address-table dynamic command in privileged EXEC mode. Is there an IP address assigned to VLAN 1? 2.9.1 Packet Tracer – Basic Switch and End Device Configuration Answers Packet Tracer – Basic Switch and End Device Configuration (Answers Version) Answers Note: Red font color or gray highlights indicate text that appears in the Answers copy only. 5) Choose Internet Protocol Version 4 (TCP/IPv4) and click Properties. a. b. Vlan1 is administratively down, line protocol is down • 1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
The selection of VLAN 99 is arbitrary and in no way implies that you should always use VLAN 99.
Clear the MAC address table. • Set up a static MAC address. With Telnet, all information, including passwords and commands, are sent across the session in plain text. 1. You are prompted to confirm deletion of this file. In this lab, PC-A and S1 reside side by side. c2960-lanbase-mz.122-25.FX.bin (may vary).
Great job, 1.1.7 Lab - Basic Switch Configuration Files, Modules 1 – 3: Basic Network Connectivity and Communications Exam Answers, Modules 4 – 7: Ethernet Concepts Exam Answers, Modules 8 – 10: Communicating Between Networks Exam Answers, Modules 11 – 13: IP Addressing Exam Answers, Modules 14 – 15: Network Application Communications Exam Answers, Modules 16 – 17: Building and Securing a Small Network Exam Answers, Modules 1 – 4: Switching Concepts, VLANs, and InterVLAN Routing Exam Answers, Modules 5 – 6: Redundant Networks Exam Answers, Modules 7 – 9: Available and Reliable Networks Exam Answers, Modules 10 – 13: L2 Security and WLANs Exam Answers, Modules 14 – 16: Routing Concepts and Configuration Exam Answers, Modules 1 – 2: OSPF Concepts and Configuration Exam Answers, Modules 3 – 5: Network Security Exam Answers, Modules 9 – 12: Optimize, Monitor, and Troubleshoot Networks Exam Answers, Modules 13 – 14: Emerging Network Technologies Exam Answers, CCNA 200-301 Dumps Full Questions – Exam Study Guide & Free. The default bias template used by the Switch Database Manager (SDM) does not provide IPv6 address capabilities.