After doing some research I found out that with wireless headset some channels on the 5g network interferes the connection. Sat 11AM - 8PM CST, Sengled Canada Your Home Hub 3000 can transmit both at the same time to optimize your Wi-Fi performance or you can choose to use only one or the other. HH3000 LAN 3 to WAN of my router. Beware my settings were reset to default. Calling them is like talking to a bag of sand. Everything should be good after that. I just got new bell internet service this week. Hi, my router is in the other side of my apartment so i'm getting bad signal. #990-355 Burrard Street I scanned the QR code on the bulb and the Sengled Home app reads, "This device is either not a Sengled WiFi bulb or is not supported." Canada: How do I connect my device to my BT Hub by Ethernet cable? The subreddit of Bell Communications, one of the largest telecommunications providers in Canada. (1,517) What you can do is connect your router to one of the LAN ports on the Home Hub 3000, connect the other side into the "Internet/WAN" port.
Mine got pushed after we had a brief power outage in Moncton last week. I've been through the same issue with them. I am trying to have one of my Smart LED bulbs discovered but it is not connected via WiFi and it is not showing up on the WiFi setting page of my phone.
However, not all dual band devices behave the same way and some device software does not cope well with a single SSID for both frequencies. JavaScript is disabled. In the Wi-Fi settings under the 5ghz there’s a channel drop down. Technical support was not helpful. https://tumblr.daught.me/post/117872159647/astro-a50-wireless-interference, Just click the drop down under Channel under Wi-Fi 5.0 GHz. And, unfortunately, their 'DMZ' really doesn't help for a lot of applications. In order for my headset to work without any interference, I need to use 5g wifi channels 48 - 116. Press J to jump to the feed. Set up my email address on my computer or device. Thanks. I can’t seem to connect my Smart LED With Touch Control (Element Touch) to my smart hub. Also, you would not need an electrician to move the fiber. The Bell Home Hub 3000 or Sagemcom FASTFast 5566 is an ADSL/VDSL modem. Your mobile device must be connected to the 2.4 GHz Wi-Fi network (5 GHz connections are not supported) of the router that you are pairing with your hub. The BT Home Hub 4, Hub 5 and BT Smart Hub are dual band with two wireless frequencies for devices to connect to: 2.4GHz and 5GHz.
TV service can possibly be worked around using pfSense but not on an EdgeRouter. Canadian TV, Computing and Home Theatre Forums. My account details My profile . This is just a community. First, make sure that the hub has been reset and has been removed from any previous Sengled accounts. A forum community dedicated to Canadian TV, computing and home theatre owners and enthusiasts. Using the same settings as before, without any VLAN tagging, and it did NOT work. New HH3000 installed. What is going on? I know this is an older post but has anyone found a new workaround at all or heard anything about a update fixing the feature? The only thing I can find on the Home Hub 3000 settings is under "Advanced Wi-Fi settings" I can only change 1 channel. When you configure regular DMZ, it asks the IP of the DMZ, it then forwards ALL packets destined for the internet facing IP, to that IP specified, thus eliminating the need for port forwards. Devices where there are known to be problems include: For some devices you can solve this problem by having different network names (SSIDs) for the 2.4GHz and the 5GHz bands. ... My service is not working. You could take the SFP out and use your own router on VLAN 35, but if you have home phone or TV service you will loose access to it. The apartment is pretty small, but for some reason, I can't get a reliable wifi connection in my bedroom (where I also have my work computer -- the computer has very slow but stable connection; in my bed, wifi drops all the time and YouTube defaults to 480p to keep up when I actually connect to the wifi). 155 Bluegrass Valley Parkway.
Just vanilla DMZ does not. Recently, We have switched to fiber op from Eastlink. Advantages. Then go onto the Bell router and disable Wifi. Regular DMZ would not require port forwarding.
The times it goofs up on me, the router just gets a 192.196.2.x IP from the router. I've been trying to get the Advanced DMZ feature working on my Bell Aliant Home Hub 3000. STE 200 I do a lot of gaming and have $400 wireless headset (Astro A50) and I'm getting a lot of interference due to having the Home Hub 3000 on my desk. Vancouver, BC V6C 2G8
Get help with device setup, troubleshooting and more. How do I reset the Sengled Smart LED With Touch Control (Element Touch) bulb? The subreddit of Bell Communications, one of the largest telecommunications providers in Canada. Press question mark to learn the rest of the keyboard shortcuts. For Bell, I remembered I need the internet user ID and password to use PPPoE. This is just a community. As of 2019-03-20, the modem supports all of the DSL speeds available from NCF (i.e. On both Hubs, the default setting has the same network name (or SSID) for both the 2.4GHz and 5GHz bands. You will get about 4 different channels to choose from and the last one I believe is 48, New comments cannot be posted and votes cannot be cast. Using your Home Hub 3000 Change your Wi-Fi network's name or password Find your Bell Internet user ID (b1) and password; Set up a guest Wi-Fi network; Set up Access (parental) controls; Find your Wi-Fi network name or password What do I do?
Canada, Sengled USA, INC. But it seems Bell is lack of experienced service engieer. Even though wireless speeds at 5GHz can be significantly faster than 2.4GHz, the range of a 5GHz connection is not as good. Why do my devices keep connecting to BT Wi-fi instead of my BT Hub? Canadian Internet, Phone, TV & Wireless Providers, Television Industry / Channels and Providers, VerticalScope Inc., 111 Peter Street, Suite 901, Toronto, Ontario, M5V 2H1, Canada. I can't find how to change channels on the router. Your mobile device must be connected to the 2.4 GHz Wi-Fi network (5 GHz connections are not supported) of the router that you are pairing with your hub.. On both Hubs, the default setting has the same network name (or SSID) for both the 2.4GHz and 5GHz bands. I had to manually add VLAN 35 and it worked right away! No speed difference.