NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the, Install On Sectional Doors With Torsion Assemblies Only, This product is intended for installation only by trained garage door technicians. Lift the door halfway up. 4.Fasten automatic door lock to the outside of the door track with hardware provided. The door should be fully closed if possible. This opener system is equipped with an unattended operation feature. To program the HomeLink repeater kit, refer to the instructions provided in the kit or visit: http://www.homelink.com/program. 1.Use the Smart Control Panel®, go to Menu > Program > Wi-Fi Setup. . ... Easy Installation. 5 Install the Door Control (Smart Control Panel®).
Register your garage door opener to receive updates and offers from LiftMaster, Send it in by texting the photo to 71403 (US) or visit www.liftmaster.photo (Global). . Install garage door opener ONLY on properly balanced and lubricated garage door. 6.Run wires through conduit, cut to proper length and strip insulation. If you are unsuccessful adding your device, try an alternate web browser. You have 20 minutes to complete the connection process. Securely tighten the 2 square head set screws closest to the motor shaft by turning the screws 1/4 - 1/2 turn after making contact with the motor shaft. 5.Remove the garage door opener from torsion bar. 3.ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener. 2.Install garage door opener ONLY on properly balanced and lubricated garage door.
8.NEVER wear watches, rings or loose clothing while installing or servicing opener. Clock Setup, Timer-to-Close, Lock, Program, Temperature, Language, Light Settings, Contrast Adjust, Maintenance Alert System, and Wi-Fi Setup. . A secondary door lock can be installed on the opposite side of the door following the instructions above.
2.Slide the garage door opener onto the end of the torsion bar. This product may require adjustments to door springs and/or track configurations. Ensure that the collar is seated all the way on motor shaft until stop is reached. 5.Position the bottom hole of the door control over the screw and slide down into place. 9.Install wall-mounted garage door control: •out of reach of small children at a minimum height of 5 feet (1.53 m) above floors, landings, steps or any other adjacent walking surface.
. Blinking - Attempting to connect to router.
. Press and release the remote control button you wish to use.
The wires can be connected to either terminal. . An unbalanced garage door might NOT reverse when required. They could be caught in garage door or opener mechanisms. Position the collar so the screws are facing out and are accessible when attached to the torsion bar. The garage door opener can be installed on either side of the door (see Planning section page 3). For a hollow torsion bar, tighten screws 3/4 - 1 full turn after making contact with the bar. This product is not intended for use on low headroom tracks with outside pickup drum or garage doors utilizing extension springs. . Refer to HomeLink Instructions Below. NOT compatible with reverse wound drums.
Wind any excess cord around cord retainer on the top side of the light base. A second cable tension monitor may be installed for additional security. Use insulated staples to secure wire in several places. . ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener. Attach the marking on or next to the emergency release. Make sure the door cable is approximately 3/4" (19 mm) from the mounting surface. See what's happening with us! Mark the location of the bottom mounting hole and drill a 5/32" (4 mm) hole. 2.Pull down on the emergency release handle until a click noise is heard. . ALWAYS call a trained door systems technician if garage door binds, sticks or is out of balance. Install a 90° conduit (not provided) or flex cable adapter (not provided) to the 7/8" hole. MyQ Remote LED Light must be installed to enable use of Timer To Close or MyQ Smartphone Control of the door. ALWAYS keep garage door in sight until completely closed. If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Route the cord through the channel so the light mounts flush. NOTE: Cable must have tension through entire door travel. .
NOTE: Do not tighten screws until instructed. Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. 4b. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding contact with vehicles to avoid accidental release. An unbalanced garage door might NOT reverse when required. Connect ground wire to the green ground screw. . NOTE: If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling. Discover the LiftMaster 8500W wall mount garage door opener.
5.Where possible, install the door operator 7 feet (2.13 m) or more above the floor. •This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement. . . Monitor your garage door, see how long it has been open, close it or open it, get optional alerts and notifications, and so much more. After ANY adjustments are made, the safety reversal system MUST be tested. The sensors can be aligned by loosening the wing nuts, aligning the sensors, and tightening the wing nuts. Attach collar to the garage door opener motor shaft. 3.To reconnect the door to the garage door opener, pull the emergency release handle straight down a second time until a click noise is heard. Related Articles. Attach warning labels to the location indicated on label. Run the white and red/white wire from the door control to the garage door opener. Plug the connector into either plug in the door opener. . Use the existing holes in the gang box. If the plug does not fit fully in the outlet, reverse the plug. Test remote control before reprogramming. They could be caught in garage door or opener mechanisms. Connect the line to the black wire and neutral to the white wire with wire nuts (not provided).